elib
DLR-Header
DLR-Logo -> http://www.dlr.de
DLR Portal Home | Imprint | Privacy Policy | Contact | Deutsch
Fontsize: [-] Text [+]

Development of an Algorithm for the Integration of a Gyroscopic Sensor in the Landing and Uprighting Phase of the MMX Rover

Gögele, Markus (2022) Development of an Algorithm for the Integration of a Gyroscopic Sensor in the Landing and Uprighting Phase of the MMX Rover. Master's, Technical University of Munich.

[img] PDF - Only accessible within DLR
8MB

Abstract

The Martian Moons eXploration (MMX) mission is planned by the Japanese space agency JAXA and will travel to Mars and its moons Phobos and Deimos. The main objective of the spacecraft is to collect a sample from Phobos. As a part of this Mission a small rover will be used to de-risk the main probe by letting it explore Phobos prior to touch down. This rover is developed by CNES and the DLR and will be released from the spacecraft approximately 50m above ground where it will then fall onto Phobos. After some bounces on the surface the rover will autonomously unfold itself, deploy solar panels and start recharging its batteries. The Problem arises from the fact that after the fall and the bounces, the folded rover could be in any orientation and therefore it is not guaranteed that the rover is able to stand up and deploy its solar panels. The current implementation to tackle this problem is to just follow a pre-defined sequence of steps blindly. As this is a very critical single point of failure of this whole sub-mission it is desirable to increase the success rate of the deployment. It is very important to get the unfolding right the first time, as if the rover tries to unfold its solar panels without being in an upright position, the mechanism could get stuck and therefore the mission would fail. Once the solar panel deployment is done, the leg movement is restricted very drastically from a free rotation to operate within a specific angle range. This fact limits further recovery attempts and therefore it is unlikely to succeed the rover mission. From early prototypes it is shown that with the help of additional sensory feedback the success rate can be increased. The hardware for the mission is already finalized an therefore only the sensor suite present at the current time can be used to supplement the uprighting process. The onboard two axis MEMS gyroscopes are the best option to be used for this purpose. The hypothesis of this thesis is, that with the help of the build-in two axis MEMS gyroscopes as feedback a better result can be achieved. As the current implementation does nothing else then doing a blind guess and hoping for the best it should yield better results when some sort of informed guess is taken, and different conditions are checked to ensure the rover does not fall over. To do this, different approaches to incorporate gyroscopic sensors in this uprighting process are collected and implemented. Finally, all implementations are evaluated and compared to the current implementation to see if they are more successful. As access to real hardware is not feasible and the environmental conditions on Phobos with its low gravity are very special, it is not possible to do those experiments on real hardware and instead it is necessary to simulate everything. The whole system, including the sensors, need to be simulated in an effort to being able to create an ensemble of simulation runs, which is necessary to infer statistic relevant information and draw a conclusion on the success of the different methods. As this also includes the sensor, it is required to create a representative model of the sensor that is comparable to the real world counterpart. This model should model all necessary noise sources and uncertainties, but at the same time it should not over complicate the already extensive simulation to keep the simulation times low. In the end there will be a big comparison between all those approaches and the current implementation to see if the hypothesis is correct and where the strengths and weaknesses of the different methods are.

Item URL in elib:https://elib.dlr.de/190212/
Document Type:Thesis (Master's)
Title:Development of an Algorithm for the Integration of a Gyroscopic Sensor in the Landing and Uprighting Phase of the MMX Rover
Authors:
AuthorsInstitution or Email of AuthorsAuthor's ORCID iDORCID Put Code
Gögele, MarkusUNSPECIFIEDUNSPECIFIEDUNSPECIFIED
Date:2022
Refereed publication:No
Open Access:No
Number of Pages:78
Status:Published
Keywords:MMX, Rover, Gyro, Simulation
Institution:Technical University of Munich
HGF - Research field:Aeronautics, Space and Transport
HGF - Program:Space
HGF - Program Themes:Space System Technology
DLR - Research area:Raumfahrt
DLR - Program:R SY - Space System Technology
DLR - Research theme (Project):R - Project MMX [SY]
Location: Oberpfaffenhofen
Institutes and Institutions:Institute of System Dynamics and Control > Space System Dynamics
Deposited By: Buse, Fabian
Deposited On:17 Nov 2022 15:34
Last Modified:25 Nov 2022 12:06

Repository Staff Only: item control page

Browse
Search
Help & Contact
Information
electronic library is running on EPrints 3.3.12
Website and database design: Copyright © German Aerospace Center (DLR). All rights reserved.