elib
DLR-Header
DLR-Logo -> http://www.dlr.de
DLR Portal Home | Impressum | Kontakt | English
Schriftgröße: [-] Text [+]

Experimental and Numerical Investigation of the Flow in a 5-Stage Transonic Compressor Rig

Lecheler. S., und Schnell, R. und Stubert, B. (2001) Experimental and Numerical Investigation of the Flow in a 5-Stage Transonic Compressor Rig. ASME Turbo-Expo 2001, 4.-7. Juni 2001, New Orleans/U.S..

Dieses Archiv kann nicht den gesamten Text zur Verfügung stellen.

Kurzfassung

The flow in a 5-stage transonic compressor rig was experimentally and numerically investigated. The rig is geometrically scaled from the front part of an existing heavy duty gas turbine compressor with CDA-blading. At several operating points pressures and temperatures were measured in order to get the performance map of the compressor, radial distributions at vane leading edges and static pressures at vanes and casing. In order to identify shock locations and to get information about the rotor-stator interactions and the flow angles, 3D L2F-measurements were done in the first and second rotor at two speeds. A newly developed double periodic measuring L2F-system was employed in order to analyze the results with respect to up- and downstream effects of both rotors. The experimental data were used for the validation and calibration of two steady 3D multistage Navier -Stokes codes with mixing plane models between the blade rows. With STAGE3D, calculations were mainly done for the first 2 transonic stages in order to compare shock locations, velocities, inlet and outlet flow angles with measurements. Furthermore the code was calibrated, which means, that grid sizes and numerical parameters were adjusted to give the best fit to the experiments while having acceptable calculation times. A set of parameters was found, which will be used for the design of new transonic multistage compressors. However not all flow quantities fit well to the measurements. Mass flow and pressures could not be fulfilled at the same time. The other code used was TRACE-S. A procedure for a fast calculation of the whole performance map for all 9 blade rows together was developed and tested. The shape of the calculated speed lines fit well to the measured ones, but the mass flow is predicted too high at off-design conditions. The reason is a too low calculated loss production which is confirmed by the higher calculated radial total pressure distributions.

Dokumentart:Konferenzbeitrag (Vortrag)
Zusätzliche Informationen: LIDO-Berichtsjahr=2004, monograph_id=2001-GT-0344,
Titel:Experimental and Numerical Investigation of the Flow in a 5-Stage Transonic Compressor Rig
Autoren:
AutorenInstitution oder E-Mail-Adresse der Autoren
Lecheler. S., ABB
Schnell, R.NICHT SPEZIFIZIERT
Stubert, B.MTU München
Datum:2001
Status:veröffentlicht
Veranstaltungstitel:ASME Turbo-Expo 2001, 4.-7. Juni 2001, New Orleans/U.S.
Veranstalter :ASME / IGTI
HGF - Forschungsbereich:Verkehr und Weltraum (alt)
HGF - Programm:keine Zuordnung
HGF - Programmthema:keine Zuordnung
DLR - Schwerpunkt:Luftfahrt
DLR - Forschungsgebiet:keine Zuordnung
DLR - Teilgebiet (Projekt, Vorhaben):NICHT SPEZIFIZIERT
Standort: Köln-Porz
Institute & Einrichtungen:Institut für Antriebstechnik
Hinterlegt von: Dr.-Ing. Rainer Schnell
Hinterlegt am:16 Sep 2005
Letzte Änderung:06 Jan 2010 13:29

Nur für Mitarbeiter des Archivs: Kontrollseite des Eintrags

Blättern
Suchen
Hilfe & Kontakt
Informationen
electronic library verwendet EPrints 3.3.12
Copyright © 2008-2013 Deutsches Zentrum für Luft- und Raumfahrt (DLR). Alle Rechte vorbehalten.